In many cases, to replace the drain hose of the washing machine requires access to its housing.
As a rule, the drain hose is made of corrugated, that is, it is corrugated, and is fixed in the middle of the machine near the drain pump.
After that, it is located along the walls of the housing of the washing machine and leads out through the back panel, sometimes at the bottom, sometimes at the top.
Contents
- How to get to the drain hose
- Changing the drain hose in an AEG, Bossx and Siemens washing machine
- Replacement of the drain hose in washing machines Аіѕton, Indеsit, Sаmsung, , Аrdo, VEKO, LG, Сandu and Whirpool
- Drainage hose replacement in European and Zanussi washing machines
- Drain hose replacement on machines with vertical load
How to get to the drain hose
That's why you have to disconnect the hose from the drain pumpand then from the body of your washing machine itself.
In order to make it more convenient for you, you can disconnect the top hatch of the machine.
Let's look at a few options for accessing the connection of the drain hose., based on the individual features of each design from the various groups and subgroups.
Changing the drain hose in the washing machine AEG, Bossh and Siemens
In these cases, the inlet to the attachment of the drain hose in washing machines of this group can be obtained through the front panel.
How to remove the front panel
Loosen the clamp and carefully detach the the boot lid from the front panel of the washing machine housing.- Remove the dispenser.
- Detach the decorative panel at the very bottom.
- Pour the remaining water out through the pump filter elementWith a rag underneath.
- Remove the screws securing the front panel to the unit. One bolt will be at the top and 2 will be at the bottom.
- Pull the lower part of the panel a little towards you, then slide it down and detach the entire panel by about 5-8 cm.
- Disconnect the cords from the blocking hole, which are on the wall, as well.
How to remove and install the drain hose
When you finally have access to the inside of your washer, remove the clamp that secures the Drain Hose And disconnect the hose from the drain structure.- Insert the new hose tightly in place of the old part, and clamp the whole thing with a clamp.
- Next, run the hose down the walls, attach it to the shell of the unit, and bring it outside.
- Connect the end of the hose (outlet) to the drain and check your installed part for tight connections.
Drain hose replacement in washing machines of Architecton, Indesit, Samsung, , Ardo, VEKO, LG, Сandu and Whirpool
In washing machines of this group, access to the hose, or rather its attachment, can be found through the bottom of the structure.
Disconnect the lowest panel that locks the pump filter.- Pour out the rest of the water, taking the greatest care to unscrew the the filter.
- Slide the washing machine forward, and when tilted back, place it near the wall.
- Starting at the bottom of the unit, unscrew all the screws securing the "snail", remove it from the housing and lower it.
When you get access to the drain hose, disconnect it from the drainage system as well, first loosen the clamp with round pliers.- Try to remember the location of your former drain hose in the middle of the housing, and then disconnect it and remove it. For convenience in this type of disassembly, we suggest removing the outer cover of the structure.
- Connect the newly purchased hose and reassemble the machine in the reverse order.
- Connect the hose to the sewer and check the leak tightness of the drain hose connections on both sides.
Replacing the drain hose of Elastronuch and Zanussi washing machines
In the Elastronuch and Zanussi washing designs, access to the elements inside is by opening the back of the panel, as the bottom is almost impossible to open, and the front panel does not open at all.
How to remove the back cover
Remove the outer cover of the washing device. To do this, unscrew the 2 fixing screws on the side of the back panel, move the cover back and detach it.- Next, you should start unscrewing the self-tapping screws at the top and a couple on the sides (you can find them under the plugs), and two or three at the bottom.
- Separate the plastic fasteners of the intake valve from the back panel and carefully detach the back panel.
How to remove and install the drain hose
After removing the back panel, we now have access to all the components. Now you need to drain the remaining water through the drain hose. To do this, lower it as low as possible and put some kind of cup and a rag in advance for safety.- Next, look for the attachment of our hose and disconnect it by loosening the clamp.
- Disconnect the hose from the body, remembering the location beforehand.
- Attach the new part in place of the old one, and fix it with a clamp.
- Connect the free end to the drain and check the level of tightness.
- Perform the assembly of the back panel in descending order of all the above steps.
Drain Hose Replacement on machines with vertical load
In order to gain access to replace the drain hose in vertical-loading machines, you only need to remove the side cover.
In order to remove the side cover, remove the screws from the end on the back of the cabinet, remove one screw from the end, from the front and from the very bottom panel. Next slide the side panel off the back panel, slide it down, and disconnect it.- After gaining access to the hose mount, loosen the clamp and remove it.
- Remove the hose from the housing and remove it from the washer-dryer.
- Install the hose in reverse order.
