In our article, we will talk about how to repair the drum of the washing machine Indesit (Indesit) yourself at home. Also, we will talk about the most common breakdowns of this machine. You will learn what tools you will need to disassemble the washing machine drum. We'll teach you how to identify bearing failures and tell you about ways to replace it with a new one.
We will bring to you how to properly disassemble the tank of the washing machine, as well as whether to repair the drum of the washing machine with your own hands.
In 99% of cases, the bearing is to blame for washing machine drum failure!
The bearing is an element of Indesit automatic washing machine device, it is installed in the drum and is the support of the shaft that rotates it. During the spin phase, the bearing experiences enormous loads, and, as a consequence, this part eventually fails. Modern inexpensive Indesit washing machines have a one-piece tank, which makes it difficult to access the bearings.
Collapsible tanks were installed on older models with a mechanical control system, such as Indesit w101. Major manufacturers of household appliances when the bearing fails, it is advised to replace the non-disassembled tank together with all parts, namely the drum, the shaft, the bearing. As a result of such repair, the cost of spare parts is more than half the cost of the washing machine itself. However, there is a way out, you can change the old bearing with your own hands at home or go to a specialized service center.
The cost of replacing the bearing will be about $ 10. To fix the problems of the washing machine associated with the failure of the drum itself, as well as its major components, you need to correctly recognize the symptoms of either breakage. So is it possible to repair the drum of the washing machine Indesit or it is better to apply to a specialized service? It is necessary to note that breakages associated with the drum of the washing machine belong to the category of serious, and lead to the fact that the washing machine finally and irrevocably goes out of operation. If you previously had no independent experience in repairing appliances, it is better not to take on this work, and to entrust it to professionals.
If you have initial skills in repairing complex home appliances, then try to fix the problem on your own, replacing the failed drum bearing. In order that the repair did not lead to even more severe breakdowns it is necessary to follow the recommendations that we give below. To repair Indesit washing machine bearings it is necessary to prepare.
At the initial stage, buy spare parts, namely glands, bearings. It is desirable to purchase original spare parts, because they are sure to fit the technique. If you have to replace the bearings, then get ready for the fact that you will have to change the glands, too, because the failure of one part often leads to failure of the other. To change a bearing we will need one short and one long Phillips head screwdriver, a wood block, a hammer, several socket wrenches or one adjustable wrench, a hex, pliers, and a flashlight.
After preparing the tools, all that remains is to prepare a workspace large enough to move the washer and provide access to the assemblies. Be warned that when working with large appliances such as a washing machine, a small room may be cramped. Repair of the washing machine begins with its disassembly. We remove the front and rear walls, trying not to damage the sealing gaskets. Next, unscrew the screws that cover the top cover of the washing machine. After this remove the lid. In order to remove the back wall it is necessary to unscrew several fixing bolts.
With the front wall of the automatic machine, the case is much more complicated:
- First of all, remove the detergent tray. To do this, pull it toward you until it stops, then lift it and pay attention.
- Unscrew the fastening screws that hold the front panel.
- Then remove the rubber sleeve and unscrew the bolts fixing the hatch lock.
- Already at the end we unscrew all the bolts of the front wall of the appliance and disconnect it.
After all the above, you will have access to the internal parts of the washing machine
Replace the oil seals at this stage will not be difficult. Let's remove the belts from the drive of the electric motor and drum pulley. Using a wooden bar, fix the pulley and remove the fasteners that hold it. Then we proceed to the removal of the drum pulley of the washing machine. The difficulty is that the pulley and drum are tightly seated on the axle. And if you apply force to the tool, it is easy to damage it. After removing the pulley, let's move on to removing the spacer bar. Once it's removed, let's start unscrewing the counterweights and pull them out.
Counterweights are usually very heavy, so we will perform this procedure slowly so as not to damage other parts of the washing machine. Then disconnect the wires from the electrical elements and unscrew the fasteners of the mobile unit, located on the drum. The screws can get rusty and can be difficult to unscrew. We will need liquid VD-40 or its equivalent. Now it's time to replace the bearing with a new one. To do this, it is necessary to dismantle the drum. To do this, let's remove the holding clamps that support the tank lid. Let's remove the seals and the lid. Carefully remove the drum along with the bearings. The gasket may be worn from time.
Then replace it with a new one. In modern models of Indesit washing machines bearings are not collapsible. It is better to press out the bearings in the service. Such indestructible bearings we ourselves will not be able to extract, here you will need not only experience, but also special tools. After pressing out the old bearings, we will install the new bearings. Once the bearings are installed, proceed to the assembly of the washing machine in reverse order.
Important!!! Even a small mistake when repairing the machine can lead to serious consequences, in order to put the technique out of operation, you should carefully study the instruction manual.
