Defining the value of Atlant washing machines errors: Overview

Atlant - A domestic washing machine that has a self-diagnostic unit. There are two types of models of this brand: with a display and with light indicators. Error codes of washing machines with display have an alphanumeric form. On machines without a display, errors are displayed on the light indicator. Fault codes are deciphered by the user himself, which will help determine and fix the breakdown.

Let's break down the error codes of both generations of Atlant washing machines.

General Information

Meaning of indicators for SoftControl and OptimaControl models

Important! First indicator is right

Errors on Atlant washing machines. Full review

Below are errors on all Atlant washing machines. In parentheses are the indicator values for machines without a display. What do the errors mean and how to fix them? Let's consider below.

Sel (all indicators not lit)

The error is a faulty program selector, that is, it simply does not work. Possibly the potentiometer, which selects the programs, is broken. The cause may be either mechanical or electronic.

To fix the problem:

The buttons need to be cleaned. They may have become dirty from frequent use and begin to stick. Check if the buttons are loose. It is possible that some of them are loose and no longer respond to pressing. You will have to replace the defective ones. Probably the selector may be broken. Check if it is in working order. It may be necessary to repair it or replace it with a new one. If the selector is good, but the problem is in the controllers connected to it. Check them and replace faulty ones.

None (lit all lights are on.)

The cause is excessive foam formation in the drum. This could be due to the use of the wrong powder (the machine does not recommend the use of powder for hand washing), or too much powder has been poured. In addition, the problem is a bad water drain or the level sensor is broken. Also, you may have set the wrong washing mode.

Fix the problem:

Unplug the washing machine, remove the items and get rid of the the foam. Adjust the mode. Next time use a different detergent or reduce the amount of detergent. If the error does not disappear after these actions, the problem is with the water level or foam sensors. Check the circuit and sensors. Replace them if necessary.

F2 (on third indicator is on.)

The error has occurred due to a temperature sensor failure. It could be broken, the contacts could be loose, or there could be something wrong with the wiring. Also the control module could be broken.

Fix F2 error:

Check the contacts and all wires. Test the circuit. You may need to repair the wiring or tighten the pins.

Check the sensor. May need to replace it.

Check control module. If defective, replace it.

F3 (lit third и fourth indicators)

Error F3 of washing machine appeared because of bad water heating. Most likely the error is due to a problem with the heating element (heating element ( TEN), broken contacts, part of wiring or breakage of control module.

Correction of error F3:

Check the voltage at the outlet. If the voltage is too low, this is the cause of error F3.

Check the wiring. If its fault between the heater, controller, and temperature sensor can be fixed, do so.

Check the contacts. They must be securely fastened.

Maybe there is no signal from the temperature sensor. Replace it.

Check heating element. The problem is in the relay or a large layer of scale. The problem with the heating element can only be solved by replacing it.

F4 (on second indicator .)

Error F4 occurs when there is a problem with the washing machine's water drainage. It means that the drain pump is broken, the drain hose is clogged, the hose is incorrectly installed, a foreign object got into the pump, the drain coupling is clogged or broken.

Correction of error F4:

• Check drain hose for kinks and blockages.
• Make sure the hose is properly installed.
• Inspect the pump. If there is debris in it, remove it. If it is broken, replace it.
• Inspect the drain coupling. There is a ball in it that may be stuck. You will have to drain the water by hand and replace the coupling. If there is a clog in it, remove it.
• Inspect the contacts and wiring. Troubleshoot the problem.
• If the problem remains, the error is due to the electronics module. It will have to be replaced.

F5 (lights are on second и fourth indicators)

The error has occurred due to insufficient filling of the tank with water. Consequently, there is a problem with the fill valve, filters, fill hose or the water system.

Solution to the problem:

Check if there is water in the pipes, if all faucets are open. Check the fill hose. Remove this hose from the washing machine. Clean and run the water. Clean the filter by the fill hose. Inspect the fill valve. It may need to be replaced. Inspect the pins and all wires in the control module and fill valve. If these steps do not correct the error, the control module will need to be replaced.

F6 (lit second и third indicators)

Most likely the error has occurred because there is a problem in the motor of the machine. The winding has overheated or the motor temperature protection contacts have disconnected.

The solution to the problem is F6:

• Check all contacts and tighten them firmly.
• Replace the motor reverser relay.
• Replace the washing machine motor.

Remember! To performing the last two operations it is better to go to к professionals at.

F7 (on fire second, third и fourth indicators)

There are obvious electrical or control unit problems.

Correct the error:

Measure the mains voltage. If it is normal (200 to 240 V), the problem is in the control unit.

Check the condition of the module and replace it if necessary.

F8 (lights up first indicator light .)

Too much water in the tank of the machine. F8 error is caused by a problem with the Pressostat, water inlet valve, cylinder leakage or control module.

Error correction:

Check pressostat and electrical circuits. Check cylinder for leaks. Test the control model. In rare cases, error F8 occurs when the water head is too high and the inlet valve is open. Replace the valve.

F9 (burns first и fourth indicators)

The problem is in the engine tachometer. It is possible that the tachogenerator or the engine is broken.

Correct the problem:

Check contacts and wiring.

Check engine tachometer and engine itself. Replace part if necessary.

F10 (burns first и third indicators)

There is no information about the hatch lock. Either the door is really badly closed or the washing machine is in error.

Correct the error F10:

Try closing the hatch more tightly and see if anything is obstructing it.

Check the electric lock and power circuits.

Verify that the sensor is working properly.

Check the electrical control module. Replace it if necessary.

Door (lights first, third и fourth indicators are lit)

The lock is broken. If the hatch is closed tightly and the electrical circuits are OK, simply replace the lock.

F12 (lit first и second indicators)

The problem is in the motor drive. Check motor to see if it is running and if motor bypass and power circuits are intact. It may be necessary to replace the part.

F13 (burns first, second и fourth indicators are lit.)

This mode is called miscellaneous faults. The system could not detect the fault and displayed error F13. Check the electrical circuits. They may be broken.

Important! To To determine problem contact к professionals at.

F14 (on fire first и second indicators are lit)

There is a failure in the software. Here you definitely need to go to a workshop to find the cause of the problem. In the worst case you will have to replace the electrical module.

F15 (в machines without display this error not provided by, but can burn all four indicators)

There is a leak. Check for leaks. If you find it, check the manhole seals, the integrity of the tank and the drainage system. Repair the leak yourself or contact an expert.