Average characteristics of washing machines "Electrolux" Before we start to analyze what causes the error code E20, it is worth knowing what is the washing machine "Electrolux". The average water consumption is 40 liters per wash. The drum capacity is 5 kilograms.
The spin speed on the spin is 1100 rpm. All these characteristics may vary depending on the model.
Electrolux machines are popular all over the world
They are reliable and convenient in their operation. For the most part, reviews about this unit are positive, it confirms the fact that the consumer trusts the Swedish manufacturer.
What does the error E20 in the washing machine "Electrolux" mean
One of the most frequent errors in washing machines "Electrolux" is an error with the code E20. This malfunction occurs when the drain system for the waste water is broken. The damage can be in the drain hose, pump, drain filter or in the electronics.
Most often, this problem can be solved by yourself without the help of specialists.
Causes of breakdowns with code E20
Trouble with the code E20, as a rule, is displayed on the display of the machine. This error informs the user of the machine that the machine cannot drain the waste water after washing. In this case, the machine may not drain water at all or may drain water, but at the same time, the signal indicating that the drum is empty does not reach the electronic module boards.
The main causes of incorrect operation of the machine are clogs or kinks in the drain hose, clogs in the drainage filter, a clogged or damaged pump, damage to the pump winding, faulty contacts leading from the pump to the control module. In the worst case scenario, the electronic module itself is broken.
Ways to make repairs
Before beginning repair work, disconnect the machine from the power supply and drain water from the drum by means of a drain hose. When draining, you should pay attention if the water comes out without any problems, then the problem is either in a clogged sewer or in the pump. Next, simply pull the laundry out of the machine and you can start troubleshooting.
First, check the siphon into which the water drains. If there are no blockages in it, you should move on to check the drain pump and the filter. After removing the filter, check it for clogs and, if there are any, get rid of them.
If the filter was clean, then proceed to remove the pump. In washing machines from "Electrolux" the pump is located near the back wall. You will need to remove the back cover of the machine and disconnect all the contacts from the pump. Then get under the bottom of the machine, there unscrew the bolt that holds the pump. Next, remove the bands from the hose for drainage and pull out the pump.
Initially, check the pump for damage. If it is damaged, it must be replaced. If outwardly it is intact, then it is worth checking it for clogs. To do this, unscrew the cover and check the impeller. Perform cleaning with caution so as not to damage the pump.
You will be lucky if the problems were related to the pump. After cleaning, install it back and run a test wash. If the drain works, everything has worked out well. However, if there is no drainage, we need to continue to diagnose the machine.
At this point, we should check the wires that lead from the pump to the control module. It's worth examining them for damage. If minor damage is present, you should use duct tape and rewire that wire. If there is major damage, the wire should be replaced.
At the very end, after a complete analysis of the hose, filter, pump and wires, you can conclude that it is about the control module. On your own to deal with such a breakdown is no longer possible, because to repair it is necessary to have the appropriate equipment and a diagram of the module boards. To fix the problem you will need to replace the burnt boards. This is a very hard and responsible job.
Prevention of blockages and malfunctions
In order to avoid malfunctions in the washing machine you need to:
- Do not use hard water for washing to avoid limescale.
- Use washing powders of high quality.
- When loading laundry, make sure that no foreign objects have entered the drum.
- From time to time, check the condition of the hose, drain filter, pump and other components.
With proper use, the machine can serve you for a long time without losing the quality of washing.
In conclusion, we can say that the error E20 is not as terrible as it may seem at first. Often this problem can be solved by yourself without any problems, but in rare cases it is necessary to resort to the help of a specialist, because only a master will be able to fix your machine.
