Average characteristics of the washing machine "Atlant". Before we figure out what causes the error f4, it is worth understanding what are the washing machines "Atlant". Appliances of this brand have a relatively low price, without losing in the quality of washing.
The average flow of water per wash is about 45 liters. The capacity of about 5 kilograms. Low power consumption. Controls are automatic.
What does f4 error mean?
All specifications may vary depending on the model. But it is safe to say that it is a quality washing machine.
Often, the code f4 occurs at the most inconvenient moment. On the display of the machine, right in the middle of the washing, this message appears. It means that the error has already occurred and it must be eliminated.
If your machine does not have a digital display, but has a self-diagnostic system, then you should pay attention to the lower set of lights. It is with the help of these LEDs that the machine reports faults. If you have a digital display, then everything will be written on it.
With either display, the f4 error means the same problem. The problem is that there are problems with the drainage of the waste liquid from the drum. When you see this code, you need to urgently take measures to repair the machine.
Causes of the breakdown
Before proceeding with the repair, it is worth finding out what exactly is preventing the drainage of dirty water.
Causes can be as simple as fixing them, and some are worth the hassle:
- The first cause could be the drain hose. The washing machine will not be able to get rid of the waste liquid if there is a clog or if the hose itself is kinked somewhere. To cope with this problem, you just need to clean and straighten the hose.
- After checking the hose, check the filter through which the drain is made. It is located on the front panel, behind the hatch. The filter should be clean and free of debris, dirt, sand, and other things. The filter should be washed and cleaned.
-
Third in line is to check the pump impeller. You need to see if it is spinning. If it is stationary, it means that there is something in the way. To fix this problem, you will need to pull out and disassemble the pump according to the diagram. Clean it and make sure that the impeller rotates.
- Also, having removed the pump, it is worth inspecting not only the impeller, but the pump as a whole. It is inspected for damage and blockages. It is also necessary to check the integrity of its winding. If this is the problem, the damage should be repaired and the winding replaced. However, if the damage is serious, it will be necessary to replace the pump completely.
- The last thing to check is the control unit. It is necessary to check the wiring harness leading from the pump directly to the circuit board. If this problem occurs, the wire is either insulated or has to be replaced. At the very end, the control board is inspected for malfunctions.
Detailed instructions for troubleshooting
The causes are now clear to us. Let's take a closer look at how to get rid of the problem. It's worth starting with the simplest one. It is necessary to disconnect the machine from the power supply and analyze the condition of the hose. Check whether it has kinks. It is also worth checking it for clogs.
If the problem is not found, then move on. It is necessary to find and wash the drain filter. Look for it in the lower right corner. After unscrewing and rinsing the filter it is worth to return it to its original place. The easiest thing to end, if the machine still gives an error, it is worth to prepare the tools and go deeper.
First, you should disconnect the machine from the water supply and sewer. Then get rid of water from the tank. After all the manipulation, for convenience, turn the machine on its left side. On the side of the bottom you will be able to see the pump. Disconnect all the wires from it, and then unscrew a few screws that hold the pump. After that, you can take the pump out of your washing machine.
Carefully inspect the pump for damage, if this is present, then the pump should be replaced. If there is a clog or the winding is damaged, then the pump should be flushed and the winding replaced.
If the f4 code continues to show up, then the next step is the hardest part. You will need to check the wires that go from the pump to the electronic module. They should be inspected for damage. If such a wire is found, it is worth using with duct tape or replacing it.
The last thing to check is the electronic module itself. Its failure is rare and it will be very difficult to repair the module on your own. If the problem is in it, then you will need to go to a specialist.
In conclusion, it is worth saying that if the error f4 appears, you should not panic. Often the machine can be repaired yourself, without resorting to the help of a specialist. In most cases, the problem is in the pump, you can easily replace it, but if the problem is in the electronics, it is better to contact a qualified specialist.
